(a) subparagraph (c)(5)(i) of this section requiring that a boiler or industrial furnace operate in accordance with operating requirements specified in the permit; and

(b) clause (c)(5)(ii)(c) of this section requiring compliance with the emission standards and operating requirements during startup and shutdown if hazardous waste is in the combustion chamber, except for particular hazardous wastes.

(a) the closure requirements of subparagraph (c)(5)(xi) of this section and paragraph (d)(12) of this section;

(b) the standards for direct transfer of subdivision (l) of this section;

(c) the standards for regulation of residues of subdivision (m) of this section; and

(d) the applicable requirements of sections 373-2.1 through 373-2.8, 373-2.28, 373-2.29, 373-3.1 through 373-3.8, 373-3.28 and 373-3.29 of this Title.

(a) subdivision (f) of this section - standards to control particulate matter;

(b) subdivision (g) of this section - standards to control metals emissions, except for mercury; and

(c) subdivision (h) of this section - standards to control hydrogen chloride and chlorine gas.

(a) Provide a one-time written notice to the commissioner indicating the following:

(b) sample and analyze the hazardous waste and other feedstocks as necessary to comply with the requirements of this paragraph by using appropriate analytical methods that are ELAP certified analytical methods. If ELAP certified methods are not available, analysis should be performed using EPA standard methods. If neither of those are available, the department will evaluate and approve proposals to use other methods to ensure that resulting data will meet data quality objectives; and

(c) maintain at the facility for at least three years records to document compliance with the provisions of this paragraph including limits on levels of toxic organic constituents and Btu value of the waste, and levels of recoverable metals in the hazardous waste compared to normal nonhazardous waste feedstocks.

(a) the hazardous waste has a total concentration of organic compounds listed in Appendix 23 of this Title (see Part 371) exceeding 500 ppm by weight, as-fired, and so is considered to be burned for destruction. The concentration of organic compounds in a waste as-generated may be reduced to the 500 ppm limit by bona fide treatment that removes or destroys organic constituents. Blending for dilution to meet the 500 ppm limit is prohibited. Documentation that the waste has not been impermissibly diluted must be retained in the records required by clause (i)(c) of this paragraph; or

(b) the hazardous waste has a heating value of 5,000 Btu/lb or more, as-fired, and so is considered to be burned as fuel. The heating value of a waste as-generated may be reduced to below the 5,000 Btu/lb limit by bona fide treatment that removes or destroys organic constituents. Blending for dilution to meet the 5,000 Btu/lb limit is prohibited. Documentation that the waste has not been impermissibly diluted must be retained in the records required by clause (i)(c) of this paragraph.

(a) the hazardous wastes listed in Appendices 51, 52 and 53 of this Title and baghouse bags used to capture metallic dusts emitted by steel manufacturing are exempt from the requirements of subparagraph (i) of this paragraph, provided that:

(b) the commissioner may decide, on a case-by-case basis, that the toxic organic constituents in a material listed in Appendix 51, 52 or 53 of this Title that contains a total concentration of more than 500 ppm toxic organic compounds, listed in Appendix 23 of this Title (see Part 371 of this Title), may pose a hazard to human health and the environment when burned in a metal recovery furnace exempt from the requirements of this section. In that situation, after adequate notice and opportunity for comment, the metal recovery furnace will become subject to the requirements of this section when burning that material. In making the hazard determination, the commissioner will consider the following factors:

(a) the owner or operator claims exemption under this paragraph;

(b) the hazardous waste is burned for legitimate recovery of precious metal; and

(c) the owner or operator will comply with the sampling and analysis and recordkeeping requirements of this paragraph; and

(a) in section 373-2.1 (General), subdivision (c);

(b) in section 373-2.2 (General facility standards), subdivisions (b) through (j);

(c) in section 373-2.3 (Preparedness and prevention), subdivisions (b) through (g);

(d) in section 373-2.4 (Contingency plan and emergency procedures), subdivisions (b) through (g);

(e) in section 373-2.5 (Manifest system, recordkeeping, and reporting), the applicable provisions of subdivisions (b) through (g);

(f) in section 373-2.6 (Releases from solid waste management units), subdivisions (a) and (l);

(g) in section 373-2.7 (Closure and post-closure), subdivisions (b) through (f);

(h) in section 373-2.8 (Financial requirements), subdivisions (b), (c), (d), (h), (i) and (j), except that the State and the Federal government are exempt from the requirements of section 373-2.8; and

(i) section 373-2.28 (Air emission standards for equipment leaks), except paragraph (a)(1).

(a) For the period beginning with initial introduction of hazardous waste and ending with initiation of the trial burn, and only for the minimum time required to bring the device to a point of operational readiness to conduct a trial burn, not to exceed a duration of 720 hours operating time when burning hazardous waste, the operating requirements must be those most likely to ensure compliance with the emission standards of subdivisions (e) through (h) of this section, based on the commissioner's engineering judgment. If the applicant is seeking a waiver from a trial burn to demonstrate conformance with a particular emission standard, the operating requirements during this initial period of operation shall include those specified by the applicable provisions of subdivisions (e) through (h) of this section. The commissioner may extend the duration of this period for up to 720 additional hours when the applicant demonstrates good cause for the extension.

(b) For the duration of the trial burn, the operating requirements must be sufficient to demonstrate compliance with the emissions standards of subdivisions (e) through (h) of this section and must be in accordance with the approved trial burn plan.

(c) For the period immediately following completion of the trial burn, and only for the minimum period sufficient to allow sample analysis, data computation, submission of the trial burn results by the applicant, review of the trial burn results and modification of the facility permit by the commissioner to reflect the trial burn results, the operating requirements must be those most likely to ensure compliance with the emission standards of subdivisions (e) through (h) of this section based on the commissioner's engineering judgment.

(d) For the remaining duration of the permit, the operating requirements must be those demonstrated in a trial burn or by alternative data specified in section 373-1.5(i) of this Title, as sufficient to ensure compliance with the emissions standards of subdivisions (e) through (h) of this section.

(a) DRE standard. Operating conditions will be specified either on a case-by-case basis for each hazardous waste burned as those demonstrated (in a trial burn or by alternative data as specified in section 373-1.5[i] of this Title) to be sufficient to comply with the destruction and removal efficiency (DRE) performance standard of paragraph (e)(1) of this section, or as those special operating requirements provided by subparagraph (e)(1)(iv) of this section for the waiver of the DRE trial burn. When the DRE trial burn is not waived under subparagraph (e)(1)(iv) of this section, each set of operating requirements will specify the composition of the hazardous waste (including acceptable variations in the physical and chemical properties of the hazardous waste which will not affect compliance with the DRE performance standard) to which the operating requirements apply. For each such hazardous waste, the permit will specify acceptable operating limits, including, but not limited to, the following conditions, as appropriate:

(b) Carbon monoxide and hydrocarbon standards. The permit must incorporate a carbon monoxide (CO) limit and, as appropriate, a hydrocarbon (HC) limit as provided by paragraphs (e)(2) through (6) of this section. The permit limits will be specified as follows:

(c) Start-up and shut-down. During start-up and shut-down of the boiler or industrial furnace, hazardous waste (except waste fed solely as an ingredient under the Tier 1 [or adjusted Tier 1] feed rate screening limits for metals and chloride/chlorine, and except low risk waste exempt from the trial burn requirements under subparagraph [e][1][v] and subdivisions [f], [g] and [h] of this section) must not be fed into the device unless the device is operating within the conditions of operation specified in the permit.

(a) Except as provided in clauses (b) and (c) of this subparagraph, the permit shall specify the following operating requirements to ensure conformance with the particulate standard specified in subdivision (f) of this section:

(b) Permit conditions to ensure conformance with the particulate matter standard shall not be provided for facilities exempt from the particulate matter standard under paragraph (f)(2) of this section.

(c) For cement kilns and light-weight aggregate kilns, permit conditions to ensure compliance with the particulate standard shall not limit the ash content of hazardous waste or other feed materials.

(a) For conformance with the Tier I (or adjusted Tier I) metals feed rate screening limits of paragraphs (g)(2) or (5) of this section, the permit shall specify the following operating requirements:

(b) For conformance with the Tier II metals emission rate screening limits under paragraph (g)(3) of this section and the Tier III metals controls under paragraph (g)(4) of this section, the permit shall specify the following operating requirements:

(c) For conformance with an alternative implementation approach approved by the commissioner under paragraph (g)(6) of this section, the permit will specify the following operating requirements:

(a) For conformance with the Tier I total chloride and chlorine feed rate screening limits of subparagraph (h)(2)(i) of this section, the permit will specify the following operating requirements:

(b) For conformance with the Tier II HCl and Cl2 emission rate screening limits under subparagraph (h)(2)(ii) of this section and the Tier III HCl and Cl ₂ controls under paragraph (h)(3) of this section, the permit will specify the following operating requirements:

(a) General requirements. As specified in subparagraphs (ii) through (v) of this paragraph, each operating parameter shall be measured, and permit limits on the parameter shall be established according to either of the following procedures:

(b) Rolling average limits for carcinogenic metals and lead. Feed rate limits for the carcinogenic metals (i.e., arsenic, beryllium, cadmium and chromium) and lead may be established either on an hourly rolling average basis as prescribed by clause (a) of this subparagraph or on (up to) a 24-hour rolling average basis. If the owner or operator elects to use an average period from two to 24 hours:

(c) Feed rate limits for metals, total chloride and chlorine, and ash. Feed rate limits for metals, total chlorine and chloride, and ash are established and monitored by knowing the concentration of the substance (i.e., metals, chloride/chlorine, and ash) in each feedstream and the flow rate of the feedstream. To monitor the feed rate of these substances, the flow rate of each feedstream must be monitored under the continuous monitoring requirements of clauses (a) and (b) of this subparagraph.

(d) Conduct of trial burn testing.

(a) Fugitive emissions. Fugitive emissions must be controlled by:

(b) Automatic waste feed cutoff. A boiler or industrial furnace must be operated with a functioning system that automatically cuts off the hazardous waste feed when operating conditions deviate from those established under this subdivision. The commissioner may limit the number of cutoffs per an operating period on a case-by-case basis. In addition:

(c) Changes. A boiler or industrial furnace must cease burning hazardous waste when changes in combustion properties, or feed rates of the hazardous waste, other fuels, or industrial furnace feedstocks, or changes in the boiler or industrial furnace design or operating conditions deviate from the limits as specified in the permit.

(a) The owner or operator must monitor and record the following, at a minimum, while burning hazardous waste:

(b) All monitors shall record data in units corresponding to the permit limit unless otherwise specified in the permit.

(c) The boiler or industrial furnace and associated equipment (pumps, valves, pipes, fuel storage tanks, etc.) must be subjected to thorough visual inspection when it contains hazardous waste, at least daily for leaks, spills, fugitive emissions, and signs of tampering.

(d) The automatic hazardous waste feed cutoff system and associated alarms must be tested at least once every seven days when hazardous waste is burned to verify operability, unless the applicant demonstrates to the commissioner that weekly inspections will unduly restrict or upset operations, and that less frequent inspections will be adequate. At a minimum, operational testing must be conducted at least once every 30 days.

(e) These monitoring and inspection data must be recorded and the records must be placed in the operating record required by section 373-2.5(c) of this Title.

(a) The purpose of this subdivision is to establish minimum national standards for owners and operators of existing boilers and industrial furnaces that burn hazardous waste where such standards define the acceptable management of hazardous waste during the period of interim status. The standards of this subdivision apply to owners and operators of existing facilities until either a Part 373 permit is issued, which includes the standards and requirements of paragraph (c)(4) of this section, or until closure responsibilities identified in this subdivision are fulfilled.

(b) Existing or in existence means a boiler or industrial furnace that, on or before August 21, 1991, is either in operation burning or processing hazardous waste, or for which construction (including the ancillary facilities to burn or to process the hazardous waste) has commenced. A facility has commenced construction if the owner or operator has obtained the Federal, State, and local approvals or permits necessary to begin physical construction; and either:

(c) If a boiler or industrial furnace is located at a facility that already has a permit or interim status, then the facility must comply with the applicable regulations dealing with permit modifications in section 373-1.7 of this Title or changes in interim status in section 373-1.3(g) of this Title.

(a) in section 373-3.1 (General), subdivision (b);

(b) in section 373-3.2 (General facility standards), subdivisions (b) through (h);

(c) in section 373-3.3 (Preparedness and prevention), subdivisions (b) through (g);

(d) in section 373-3.4 (Contingency plan and emergency procedures), subdivisions (b) through (g);

(e) in section 373-3.5 (Manifest system, recordkeeping, and reporting), subdivisions (b) through (g), except that subdivisions (b) and (f) do not apply to owners and operators of on-site facilities that do not receive any hazardous waste from off-site sources;

(f) in section 373-3.7 (Closure and post-closure), subdivisions (b) through (f);

(g) in section 373-3.8 (Financial requirements), subdivisions (b), (c), (d), (h) and (i), except that the State and the Federal government are exempt from the requirements of section 373-3.8; and

(h) section 373-3.28 (Air emission standards for equipment leaks), except paragraph (a)(1).

(a) Controls.

(b) Burning hazardous waste solely as an ingredient. A hazardous waste is burned for a purpose other than solely as an ingredient if it meets either of these criteria:

(a) hazardous waste may be burned solely as an ingredient; or

(b) hazardous waste may be burned for purposes of compliance testing (or testing prior to compliance testing) for a total period of time not to exceed 720 hours; or

(c) such waste may be burned if the commissioner has documentation to show that, prior to August 21, 1991:

(d) such waste may be burned in a halogen acid furnace if the waste was burned as an excluded ingredient under section 371.1(c)(6) of this Title prior to February 21, 1991 and documentation is kept on file supporting this claim.

(a) General facility information:

(b) Except for facilities complying with the Tier I or adjusted Tier I feed rate screening limits for metals or total chlorine and chloride provided by paragraphs (g)(2) or (5) of this section, and subparagraph (h)(2)(i) or paragraph (h)(5) of this section, respectively, the estimated uncontrolled (at the inlet to the air pollution control system) emissions of particulate matter, each metal controlled by subdivision (g) of this section, and hydrogen chloride and chlorine, and the following information to support such determinations:

(c) For facilities complying with the Tier I or adjusted Tier I feed rate screening limits for metals or total chlorine and chloride provided by paragraphs (g)(2) or (5) of this section and subparagraph (h)(2)(i) or paragraph (h)(5) of this section, the feed rate (lb/hr) of total chloride and chlorine, antimony, arsenic, barium, beryllium, cadmium, chromium, lead, mercury, silver, and thallium in each feed stream (hazardous waste, other fuels, industrial furnace feedstocks).

(d) For facilities complying with the Tier II or Tier III emission limits for metals or HCl and Clz ₂ (under paragraphs [g][3] or [4] or subparagraph [h][2][ii] or paragraph [h][3] of this section), the estimated controlled (outlet of the air pollution control system) emissions rates of particulate matter, each metal controlled by subdivision (g) of this section, and HCl and Cl ₂, and the following information to support such determinations:

(e) Determination of allowable emissions rates for HCl, Cl ₂, antimony, arsenic, barium, beryllium, cadmium, chromium, lead, mercury, silver, and thallium, and the following information to support such determinations:

(f) For facilities complying with the Tier II or III emissions rate controls for metals or HCl and Cl ₂, a comparison of the estimated controlled emissions rates determined under clause (d) of this subparagraph with the allowable emission rates determined under clause (e) of this subparagraph.

(g) For facilities complying with the Tier I (or adjusted Tier I) feed rate screening limits for metals or total chloride and chlorine, a comparison of actual feed rates of each metal and total chlorine and chloride determined under clause (c) of this subparagraph to the Tier I allowable feed rates.

(h) For industrial furnaces that feed hazardous waste for any purpose other than solely as an ingredient (as defined by clause [1][v] [b] of this subdivision) at any location other than the product discharge end of the device, documentation of compliance with the requirements of subclauses (1)(v)(a)(1), (2) and (3) of this subdivision.

(i) For industrial furnaces that recycle collected particulate matter (PM) back into the furnace and that will certify compliance with the metals emissions standards under subclause (3)(iii)(b)(1) of this subdivision:

(a) feed rate of total hazardous waste and (unless complying with the Tier I or adjusted Tier I metals feed rate screening limits under paragraphs [g][2] or [5] of this section) pumpable hazardous waste;

(b) feed rate of each metal in the following feed streams:

(c) total feed rate of chlorine and chloride in total feed streams;

(d) total feed rate of ash in total feed streams, except that the ash feed rate for cement kilns and light-weight aggregate kilns is not limited; and

(e) maximum production rate of the device in appropriate units when producing normal product, unless complying with the Tier I or adjusted Tier I feed rate screening limits for chlorine under subparagraph (h)(2)(i) or paragraph (h)(5) of this section and for all metals under paragraphs (g)(2) or (5) of this section, and the uncontrolled particulate emissions do not exceed the standard under subdivision (f) of this section.

(a) General requirements. Limits on each of the parameters specified in subparagraph (iii) of this paragraph (except for limits on metals concentrations in collected particulate matter [PM] for industrial furnaces that recycle collected PM) shall be established and continuously monitored under either of the following methods:

(b) Rolling average limits for carcinogenic metals and lead. Feed rate limits for the carcinogenic metals (arsenic, beryllium, cadmium, and chromium) and lead may be established either on an hourly rolling average basis as prescribed by subclause (a)(2) of this subparagraph or on (up to) a 24-hour rolling average basis. If the owner or operator elects to use an averaging period from two to 24 hours:

(c) Feed rate limits for metals, total chloride and chlorine, and ash. Feed rate limits for metals, total chlorine and chloride, and ash are established and monitored by knowing the concentration of the substance (i.e., metals, chloride/chlorine, and ash) in each feedstream and the flow rate of the feedstream. To monitor the feed rate of these substances, the flow rate of each feedstream must be monitored under the continuous monitoring requirements of clauses (a) and (b) of this subparagraph.

(a) name and address of the owner and operator of the facility as well as the location of the device burning hazardous waste;

(b) date that the certification of precompliance was submitted to the EPA administrator;

(c) brief description of the regulatory process required to comply with the interim status requirements of this subdivision including required emissions testing to demonstrate conformance with emissions standards for organic compounds, particulate matter, metals, and HCl and Cl₂;

(d) types and quantities of hazardous waste burned, including, but not limited to, source, whether solids or liquids, as well as an appropriate description of the waste;

(e) type of device(s) in which the hazardous waste is burned, including a physical description and maximum production rate of each device;

(f) types and quantities of other fuels and industrial furnace feedstocks fed to each unit;

(g) brief description of the basis for this certification of precompliance as specified in subparagraph (ii) of this paragraph;

(h) locations where the record for the facility can be viewed and copied by interested parties. These records and locations shall, at a minimum, include:

(i) notification of the establishment of a facility mailing list, whereby interested parties shall notify the agency that they wish to be placed on the mailing list to receive future information and notices about this facility; and

(j) location (mailing address) of the applicable EPA regional office, hazardous waste division, where further information can be obtained on EPA regulation of hazardous waste burning.

(a) The public notice requirements of subparagraph (vi) of this paragraph do not apply to recertifications.

(b) The owner and operator must operate the facility within the limits established for the operating parameters under subparagraph (iii) of this paragraph until a revised certification is submitted under this subparagraph or a certification of compliance is submitted under paragraph (3) of this subdivision.

(a) Feed rate of total hazardous waste and (unless complying with the Tier I or adjusted Tier I metals feed rate screening limits under paragraphs[g][2] or [5] of this section), pumpable hazardous waste.

(b) Feed rate of each metal in the following feedstreams:

(c) total feed rate of chlorine and chloride in total feed streams, except that facilities that comply with Tier I or adjusted Tier I feed rate screening limits may set their operating limits at the total chlorine and chloride feed rate screening limits determined under subparagraph (h)(2)(i) or paragraph (h)(5) of this section;

(d) total feed rate of ash in total feed streams, except that the ash feed rate for cement kilns and light-weight aggregate kilns is not limited;

(e) carbon monoxide concentration, and where required, hydrocarbon concentration in stack gas. When complying with the CO controls of paragraph (e)(2) of this section, the CO limit is 100 ppmv, and when complying with the HC controls of paragraph (e)(3) of this section, the HC limit is 20 ppmv. When complying with the CO controls of paragraph (e)(3) of this section, the CO limit is established based on the compliance test;

(f) maximum production rate of the device in appropriate units when producing normal product, (unless complying with the Tier I or adjusted Tier I feed rate screening limits for chlorine under subparagraph [h][2] [i] or paragraph [h][5] of this section and for all metals under paragraphs [g][2] or [5] of this section, and the uncontrolled particulate emissions do not exceed the standard under subdivision [f] of this section);

(g) maximum combustion chamber temperature where the temperature measurement is as close to the combustion zone as possible and is upstream of any quench water injection (unless complying with the Tier I or adjusted Tier I metals feed rate screening limits under paragraphs [g][2] or [5] of this section);

(h) maximum flue gas temperature entering a particulate matter control device (unless complying with Tier I or adjusted Tier I metals feed rate screening limits under paragraphs [g][2] or [5] of this section and the total chlorine and chloride feed rate screening limits under paragraphs [h][2] or [5] of this section);

(i) for systems using wet scrubbers, including wet ionizing scrubbers (unless complying with Tier I or adjusted Tier I metals feed rate screening limits under paragraphs [g][2] or [5] of this section and the total chlorine and chloride feed rate screening limits under subparagraph [h][2][i] or paragraph [h][5] of this section):

(j) for systems using venturi scrubbers, the minimum differential gas pressure across the venturi (unless complying with the Tier I or adjusted Tier I metals feed rate screening limits under paragraphs [g][2] or [5] of this section and the total chlorine and chloride feed rate screening limits under subparagraph [h][2][i] or paragraph [h][5] of this section);

(k) for systems using dry scrubbers (unless complying with the Tier I or adjusted Tier I metals feed rate screening limits under paragraphs [g][2] or [5] of this section and the total chlorine and chloride feed rate screening limits under subparagraph [h][2][i] or paragraph [h][5] of this section):

(l) for systems using wet ionizing scrubbers or electrostatic precipitators (unless complying with the Tier I or adjusted Tier I metals feed rate screening limits under paragraphs [g][2] or [5] of this section and the total chlorine and chloride feed rate screening limits under subparagraph [h][2][i] or paragraph [h][5] of this section):

(m) for systems using fabric filters (baghouses), the minimum pressure drop (unless complying with the Tier I or adjusted Tier I metal feed rate screening limits under paragraphs [g][2] or [5] of this section and the total chlorine and chloride feed rate screening limits under subparagraph [h][2][i] or paragraph [h][5] of this section).

(a) general facility information including:

(b) specific information on each device to be tested including:

(c) information on the testing planned, including a complete copy of the test protocol and quality assurance/quality control (QA/QC) plan, and a summary description for each test providing the following information, at a minimum:

(a) General. Compliance testing must be conducted under conditions for which the owner or operator has submitted a certification of precompliance under paragraph (2) of this subdivision and under conditions established in the notification of compliance testing required by subparagraph (ii) of this paragraph. The owner or operator may seek approval on a case-by-case basis to use compliance test data from one unit in lieu of testing a similar onsite unit. To support the request, the owner or operator must provide a comparison of the hazardous waste burned and other feedstreams, and the design, operation, and maintenance of both the tested unit and the similar unit. The commissioner shall provide a written approval to use compliance test data in lieu of testing a similar unit if the commissioner finds that the hazardous wastes, the devices, and the operating conditions are sufficiently similar, and the data from the other compliance test is adequate to meet the requirements of this paragraph.

(b) Special requirements for industrial furnaces that recycle collected PM. Owners and operators of industrial furnaces that recycle back into the furnace particulate matter (PM) from the air pollution control system must comply with one of the following procedures for testing to determine compliance with the metals standards of paragraphs (g)(3) or (4) of this section:

(c) Conduct of compliance testing.

(a) General facility and testing information including:

(b) Specific information on each test, including:

(c) Comparison of the actual emissions during each test with the emissions limits prescribed by paragraphs (e)(2), (3) and (5) and subdivisions (f), (g) and (h) of this section and established for the facility in the certification of precompliance under paragraph (2) of this subdivision.

(d) Determination of operating limits based on all valid runs of the compliance test for each applicable parameter listed in subparagraph (i) of this paragraph using either of the following procedures:

(e) Certification of compliance statement. The following statement shall accompany the certification of compliance:

(a) when complying with the requirements of subclause (iii)(b)(1) of this paragraph, comply with the operating requirements prescribed in “Alternative Method to Implement the Metals Controls” in Appendix 49 of this Title; and

(b) when complying with the requirements of subclause (iii)(b)(2) of this paragraph, comply with the operating requirements prescribed by that subclause.

(a) If the owner or operator did not submit a complete certification of compliance to the EPA administrator for all of the applicable emissions standards of subdivisions (e) through (h) by August 21, 1992, he/she must either:

(b) The owner or operator may request a case-by-case extension of time to extend any time limit provided by paragraph (3) of this subdivision if compliance with the time limit is not practicable for reasons beyond the control of the owner or operator.

(a) prior to submittal of a revised certification of compliance, hazardous waste may not be burned for more than a total of 720 hours under operating conditions that exceed those established under a current certification of compliance, and such burning may be conducted only for purposes of determining whether the facility can operate under revised conditions and continue to meet the applicable emissions standards of subdivisions (e) through (h) of this section;

(b) at least 30 days prior to first burning hazardous waste under operating conditions that exceed those established under a current certification of compliance, the owner or operator shall notify the commissioner and submit the following information:

(c) conduct a compliance test under the revised operating conditions and the protocol submitted to the commissioner to determine compliance with the applicable emissions standards of subdivisions (e) through (h) of this section; and

(d) submit a revised certification of compliance under subparagraph (iv) of this paragraph.

(a) if compliance with the combustion chamber temperature limit is based on an hourly rolling average, the minimum temperature during the compliance test is considered to be the average over all runs of the lowest hourly rolling average for each run; or

(b) if compliance with the combustion chamber temperature limit is based on an instantaneous temperature measurement, the minimum temperature during the compliance test is considered to be the time-weighted average temperature during all runs of the test; and

(a) feed rates and composition of hazardous waste, other fuels, and industrial furnace feed stocks, and feed rates of ash, metals, and total chloride and chlorine as necessary to ensure conformance with the certification of precompliance or certification of compliance;

(b) carbon monoxide (CO), oxygen, and if applicable, hydrocarbons (HC), on a continuous basis at a common point in the boiler or industrial furnace downstream of the combustion zone and prior to release of stack gases to the atmosphere in accordance with the operating limits specified in the certification of compliance. CO, HC, and oxygen monitors must be installed, operated, and maintained in accordance with methods specified in Appendix 49 of this Title;

(c) upon the request of the commissioner, sampling and analysis of the hazardous waste (and other fuels and industrial furnace feed stocks as appropriate) and the stack gas emissions must be conducted to verify that the operating conditions established in the certification of precompliance or certification of compliance achieve the applicable standards of subdivisions (e) through (h) of this section.

(a) The feed rate screening limits for antimony, barium, mercury, thallium, and silver are based on either:

(b) The feed rate screening limit for lead is based on one of the following:

(a) The feed rates of arsenic, cadmium, beryllium, and chromium in all feed streams, including hazardous waste, fuels, and industrial furnace feed stocks shall not exceed values derived from the screening limits specified in Appendix 41 of this Title. The feed rate of each of these metals is limited to a level such that the sum of the ratios of the actual feed rate to the feed rate screening limit specified in Appendix 41 of this Title shall not exceed 1.0, as provided by the following equation:

(b) The feed rate screening limits for the carcinogenic metals are based on either:

(a) The terrain-adjusted effective stack height is determined according to the following equation:

(b) The stack height (Ha) may not exceed good engineering practice as specified in 40 CFR 51.100(ii) (see section 370.1[e] of this Title).

(c) If the TESH for a particular facility is not listed in the table in the appendices, the nearest lower TESH listed in the table shall be used. If the TESH is four meters or less, a value of four meters shall be used.

(a) the device is located in a narrow valley less than one kilometer wide;

(b) the device has a stack taller than 20 meters and is located such that the terrain rises to the physical height within one kilometer of the facility;

(c) the device has a stack taller than 20 meters and is located within five kilometers of a shoreline of a large body of water such as an ocean or large lake;

(d) the physical stack height of any stack is less than 2.5 times the height of any building within five building heights or five projected building widths of the stack and the distance from the stack to the closest boundary is within five building heights or five projected building widths of the associated building; or

(e) the commissioner determines that standards based on site-specific dispersion modeling are required.

(a) Owners and operators of facilities with more than one onsite stack from a boiler, industrial furnace, incinerator, or other thermal treatment unit subject to controls on metals emissions under a Part 373 operating permit or interim status controls must comply with the emissions screening limits for any such stacks assuming all hazardous waste is fed into the device with the worst-case stack based on dispersion characteristics.

(b) The worst-case stack is determined by procedures provided in subparagraph (2)(vi) of this subdivision.

(c) For each metal, the total emissions of the metal from those stacks shall not exceed the screening limit for the worst-case stack.

(a) for each noncarcinogenic metal, by back-calculating from the RAC provided in Appendix 44 of this Title to determine the allowable emission rate for each metal using the dilution factor for the maximum annual average ground level concentration predicted by dispersion modeling in conformance with paragraph (8) of this subdivision; and

(b) for each carcinogenic metal by:

(a) The worst-case stack is determined by procedures provided in subparagraph (g)(2)(vi) of this section.

(b) Under Tier I, the total feed rate of chlorine and chloride to all subject devices shall not exceed the screening limit for the worst-case stack.

(c) Under Tier II, the total emissions of HCl and Cl₂ from all subject stacks shall not exceed the screening limit for the worst-case stack.

(a) a minimum of 50 percent of fuel fired to the device shall be fossil fuel, fuels derived from fossil fuel, tall oil, or, if approved by the commissioner on a case-by-case basis, other nonhazardous fuel with combustion characteristics comparable to fossil fuel. Such fuels are termed primary fuel for purposes of this subdivision. (Tall oil is a fuel derived from vegetable and rosin fatty acids.) The 50 percent primary fuel firing rate shall be determined on a total heat or mass input basis, whichever results in the greater mass feed rate of primary fuel fired;

(b) primary fuels and hazardous waste fuels shall have a minimum as-fired heating value of 8,000 Btu/lb;

(c) the hazardous waste is fired directly into the primary fuel flame zone of the combustion chamber; and

(d) the device operates in conformance with the carbon monoxide controls provided by subparagraph (e)(2)(i) of this section. Devices subject to the exemption provided by this subdivision are not eligible for the alternative carbon monoxide controls provided by paragraph (e)(3) of this section.

(a) identify and quantify those nonmetal compounds listed in Appendix 23 of this Title (see Part 371 of this Title) that could reasonably be expected to be present in the hazardous waste. The constituents excluded from analysis must be identified and the basis for their exclusion explained;

(b) calculate reasonable, worst case emission rates for each constituent identified in clause (a) of this subparagraph by assuming the device achieves 99.9 percent destruction and removal efficiency. That is, assume that 0.1 percent of the mass weight of each constituent fed to the device is emitted;

(c) for each constituent identified in clause (a) of this subparagraph, use emissions dispersion modeling to predict the maximum annual average ground level concentration of the constituent.

(d) Ground level concentrations of constituents predicted under clause (c) of this subparagraph must not exceed the following levels:

(a) Direct transfer equipment means any device (including but not limited to, such devices as piping, fittings, flanges, valves, and pumps) that is used to distribute, meter, or control the flow of hazardous waste between a container (i.e., transport vehicle) and a boiler or industrial furnace.

(b) Container means any portable device in which hazardous waste is transported, stored, treated, or otherwise handled, and includes transport vehicles that are containers themselves (e.g., tank trucks, tanker-trailers, and rail tank cars), and containers placed on or in a transport vehicle.

(a) generate extreme heat or pressure, fire, explosion, or violent reaction;

(b) produce uncontrolled toxic mists, fumes, dusts, or gases in sufficient quantities to threaten human health;

(c) produce uncontrolled flammable fumes or gases in sufficient quantities to pose a risk of fire or explosions;

(d) damage the structural integrity of the container or direct transfer equipment containing the waste;

(e) adversely affect the capability of the boiler or industrial furnace to meet the standards provided by subdivisions (e) through (h) of this section; or

(f) threaten human health or the environment.

(a) spill prevention controls (e.g., check valves, dry discount couplings); and

(b) automatic waste feed cutoff to use if a leak or spill occurs from the direct transfer equipment.

(a) The owner or operator must inspect at least once each operating hour when hazardous waste is being transferred from the transport vehicle (container) to the boiler or industrial furnace:

(b) The owner or operator must inspect cathodic protection systems, if used, to ensure that they are functioning properly according to the schedule provided by section 373 3.10(f)(2) of this Title.

(c) Records of inspections made under this subparagraph shall be maintained in the operating record at the facility, and available for inspection for at least three years from the date of the inspection.

(a) normal residue. Concentrations of toxic constituents of concern in normal residue shall be determined based on analyses of a minimum of 10 samples representing a minimum of 10 days of operation. Composite samples may be used to develop a sample for analysis provided that the compositing period does not exceed 24 hours. The upper tolerance limit (at 95 percent confidence with a 95 percent proportion of the sample distribution) of the concentration in the normal residue shall be considered the statistically-derived concentration in the normal residue. If changes in raw materials or fuels reduce the statistically-derived concentrations of the toxic constituents of concern in the normal residue, the statistically-derived concentrations must be revised or statistically-derived concentrations of toxic constituents in normal residue must be established for a new mode of operation with the new raw material or fuel. To determine the upper tolerance limit in the normal residue, the owner or operator shall use statistical procedures prescribed in "Statistical Methodology for Bevill Residue Determinations" in Appendix 49 of this Title;

(b) waste-derived residue. Waste-derived residue shall be sampled and analyzed as often as necessary to determine whether the residue generated during each 24-hour period has concentrations of toxic constituents that are higher than the concentrations established for the normal residue under clause (a) of this subparagraph. If so, hazardous waste burning has significantly affected the residue and the residue shall not be excluded from the definition of a hazardous waste. Concentrations of toxic constituents of concern in the waste derived residue shall be determined based on analysis of one or more samples obtained over a 24-hour period. Multiple samples may be analyzed, and multiple samples may be taken to form a composite sample for analysis provided that the sampling period does not exceed 24 hours. If more than one sample is analyzed to characterize waste- derived residues generated over a 24-hour period, the concentration of each toxic constituent shall be the arithmetic mean of the concentrations in the samples. No results may be disregarded; or

(a) nonmetal constituents. The concentration of each nonmetal toxic constituent of concern (specified in subparagraph (i) of this paragraph) in the waste-derived residue must not exceed the health-based level specified in Appendix 47 of this Title, or the level of detection, whichever is higher. If a health-based limit for a constituent of concern is not listed in Appendix 47 of this Title, then a limit of 0.002 micrograms per kilogram or the level of detection, whichever is higher, must be used. The concentration of each non-metal toxic constituent of concern and the level of detection must be established through the use of appropriate analytical methods that are ELAP certified analytical methods. If ELAP certified methods are not available, analysis should be performed using EPA standard methods. If neither of those are available, the department will evaluate and approve proposals to use other methods to ensure that resulting data will meet data quality objectives. The levels specified in Appendix 47 of this Title (and the default level of 0.002 micrograms per kilogram or the level of detection for constituents as identified in Note 1 of Appendix 47 of this Title) are administratively stayed under the condition, for those constituents specified in subparagraph (i) of this paragraph, that the owner or operator complies with alternative levels defined as the land disposal restriction limits specified in section 376.4(d) of this Title for F039 nonwastewaters. In complying with those alternative levels, if an owner or operator is unable to detect a constituent despite documenting use of best good-faith efforts as defined by applicable EPA guidance or standards, the owner or operator is deemed to be in compliance for that constituent. Until new guidance or standards are developed, the owner or operator may demonstrate such good-faith efforts by achieving a detection limit for the constituent that does not exceed an order of magnitude above the level provided by section 376.4(d) of this Title for F039 nonwastewaters. In complying with the section 376.4(d) of this Title F039 nonwastewater levels for polychlorinated dibenzo-p-dioxins and polychlorinated dibenzo-furans, (unless the owner or operator complies with alternative levels defined as the land disposal restriction limits specified in section 376.4(d) of this Title for F039 nonwastewaters,) analyses must be performed for total hexachlorodibenzo-p-dioxins, total hexachlorodibenzofurans, total pentachlorodibenzo-p-dioxins, total pentachlorodibenzofurans, total tetrachlorodibenzo-p-dioxins, and total tetrachlorodibenzofurans; and

(b) metal constituents. The concentration of metals in an extract obtained using the Toxicity Characteristic Leaching Procedure of section 371.3(e) of this Title must not exceed the levels specified in Appendix 47 of this Title; and

(c) sampling and analysis. Waste-derived residue shall be sampled and analyzed as often as necessary to determine whether the residue generated during each 24-hour period has concentrations of toxic constituents that are higher than the health-based levels. Concentrations of toxic constituents of concern in the waste-derived residue shall be determined based on analysis of one or more samples obtained over a 24-hour period. Multiple samples may be analyzed, and multiple samples may be taken to form a composite sample for analysis provided that the sampling period does not exceed 24 hours. If more than one sample is analyzed to characterize waste-derived residues generated over a 24-hour period, the concentration of each toxic constituent shall be the arithmetic mean of the concentrations in the samples. No results may be disregarded; and

(a) the levels of constituents in Appendix 23 of this Title that are present in normal residues; and

(b) data and information, including analyses of samples as necessary, obtained to determine if changes in raw materials or fuels would reduce the concentration of toxic constituents of concern in the normal residue.