Home Table of Contents

§ 1607. Marking of Appliances.

20 CA ADC § 1607BARCLAYS OFFICIAL CALIFORNIA CODE OF REGULATIONS

Barclays Official California Code of Regulations Currentness
Title 20. Public Utilities and Energy
Division 2. State Energy Resources Conservation and Development Commission
Chapter 4. Energy Conservation
Article 4. Appliance Efficiency Regulations (Refs & Annos)
20 CCR § 1607
§ 1607. Marking of Appliances.
(a) Scope of Section 1607.
Every unit of every appliance within the scope of section 1601 of this Article shall comply with the applicable provisions of this section. The effective dates of this section shall be the same as the effective dates shown in section 1605.1, 1605.2 or 1605.3 of this Article for appliances for which there is an energy efficiency, energy consumption, energy design, water efficiency, water consumption, or water design standard in section 1605.1, 1605.2, or 1605.3 of this Article. For appliances with no energy efficiency, energy consumption, energy design, water efficiency, water consumption, or water design standard in section 1605.1, 1605.2, or 1605.3 of this Article, the effective date of this section shall be January 1, 2006.
(b) Name, Model Number, and Date.
Except as provided in section 1607(c) of this Article, the following information shall be permanently, legibly, and conspicuously displayed on an accessible place on each unit;
(1) manufacturer's name or brand name or trademark (which shall be either the name, brand, or trademark of the listed manufacturer specified pursuant to section 1606(a)(2)(A) of this Article;
(2) model number; and
(3) date of manufacture, indicating (i) year and (ii) month or smaller (e.g. week) increment. If the date is in a code that is not readily understandable to the layperson, the manufacturer shall immediately, on request, provide the code to the Energy Commission.
(c) Exceptions to Section 1607(b).
(1) For plumbing fixtures and plumbing fittings, the information required by section 1607(b) of this Article shall be permanently, legibly, and conspicuously displayed on an accessible place on each unit or on the unit's packaging.
(2) For lamps and spray sprinkler bodies, the information required by section 1607(b) of this Article shall be permanently, legibly, and conspicuously displayed on an accessible place on each unit, on the unit's packaging, or, where the unit is contained in a group of several units in a single package, on the packaging of the group.
(3) For fluorescent lamp ballasts, the date of manufacture information required by section 1607(b)(3) of this Article shall indicate (i) year and(ii) three-month or smaller increment. If the date is in a code that is not readily understandable to the layperson, the manufacturer shall immediately, on request, provide the code to the Energy Commission.
(d) Energy Performance Information.
(1) Federally Regulated Consumer Products.
The marking required by 16 C.F.R. part 305 shall be displayed as required for all federally regulated consumer products of the following classes:
Refrigerators Refrigerator-freezers Freezers Central air conditioners Heat pumps Dishwashers Water heaters Room air conditioners Warm air furnaces Boilers Pool heaters Clothes washers Fluorescent lamp ballasts Showerheads Faucets Water closets Urinals General service fluorescent lamps General service incandescent reflector lamps General service incandescent (other than reflector) lamps Medium-base compact fluorescent lamps Metal halide lamp fixtures Televisions Ceiling fans.
(2) Federally Regulated Commercial and Industrial Equipment.
Unless otherwise specified in Table Y, each unit of an appliance listed in Table Y that is federally regulated commercial and industrial equipment shall be marked, permanently and legibly on an accessible and conspicuous place on the unit, with the applicable energy performance information shown in Table Y, and such information shall also be included on all printed material that is displayed or distributed at the point of sale.
Table Y
Requirements for Marking of Federally-Regulated Commercial and Industrial Equipment
(3) Air Conditioners, Heat Pumps, Furnaces, Boilers, and Water Heaters. Each unit of air conditioners, heat pumps, furnaces, boilers, and water heaters that are not subject to NAECA and that comply with the provisions in Tables 6.8.1 A through F of ANSI/ASHRAE/IES Standard 90.1-2007 shall be marked, permanently and legibly on an accessible and conspicuous place on the unit, with a statement that the equipment complies with the requirements of ASHRAE Standard 90.1.
(4) Distribution Transformers. Each unit of distribution transformers shall have a label or nameplate which states “DOE Compliant” or equivalent.
(5) Illuminated Exit Signs. Each unit of illuminated exit signs meeting the criteria of section 1605.1(l) of this Article that are sold in California (subject to the limitations of section 1601 of this Article) shall be marked by the manufacturer with a block E inside a circle; the mark commonly referred to as “Circle E.” The size of the mark shall be commensurate with other markings on the sign, but not smaller than 1/4 inch. Signs not meeting section 1605.1(l) of this Article shall not be so marked.
(6) Luminaires. Each unit of torchieres and each package containing a torchiere shall be marked, permanently and legibly on an accessible and conspicuous place on the unit, in characters no less than 1/8 inch on the inner surface of the reflector bowl of the torchiere, and 1/4 inch on the packaging, “LAMPS MUST TOTAL NO MORE THAN 190 WATTS - TORCHIERE IS NON-COMPLIANT IF IT IS ABLE TO DRAW MORE THAN 190 WATTS.”
(7) Commercial Pre-Rinse Spray Valves. Each unit of commercial pre-rinse spray valve shall be marked, permanently and legibly on an accessible and conspicuous place on the unit, in characters no less than 1/8 inch, the flow rate of the unit, in gallons-per minute (gpm) at 60 psi.
(8) External Power Supplies.
(A) Federally Regulated External Power Supplies. Any external power supply subject to the standards in section 1605.1(u)(1) of this Article shall be clearly and permanently marked in accordance with 10 C.F.R. section 430.32(w)(4).
(B) State-Regulated External Power Supplies. Any state-regulated external power supply complying with the requirements of section 1605.3(u) shall be clearly and permanently marked in accordance with the International Efficiency Marking Protocol for External Power Supplies, Version 3.0, September 2013.
(9) Residential Pool Pumps.
(A) Each residential pool pump shall be marked, permanently and legibly on an accessible and conspicuous place on the unit, in characters no less than 1/4 inch, the nameplate HP of the pump.
(B) Each residential pool pump motor shall be marked, permanently and legibly on an accessible and conspicuous place on the unit, in characters no less than 1/4 inch, the pool pump motor capacity of the motor.
(C) Two-, multi-, or variable-speed residential pool pumps certified under section 1606 of this Article on or after January 1, 2010 shall be marked, permanently and legibly on an accessible and conspicuous place on the unit, in characters no less than 1/4 inch, “This pump must be installed with a two-, multi-, or variable-speed pump motor controller.”
(10) Battery Charger Systems. Each state-regulated battery charger system shall be marked with a “BC” inside a circle. The marking shall be legible and permanently affixed to:
(A) the product nameplate that houses the battery charging terminal or;
(B) the retail packaging and, if included, the cover page of the instructions.
(11) Emergency Lighting and Self-Contained Lighting Controls. All occupant sensing devices which utilize microwave radiation for detection of occupants shall be marked with an approved Federal Communications Commission identifier. In addition, such devices must have permanently affixed installation instructions recommending that the device be installed at least 12 inches from any area normally used by room occupants.
(12) Air Filters. Each unit of air filters manufactured on or after April 1, 2019, shall be marked, permanently and legibly, on an accessible and conspicuous place on the edge of the filter itself or on the pleats, in characters of font size 12, with the information specified in either section (A) or (B) below as applicable to the air filter model:
(A) Air filters for which the reported information is determined in accordance with the AHRI standard 680-2009 shall be marked with the following information:
1. Particle size efficiency (PSE) of the unit in three particle size ranges: 0.3-1.0, 1.0-3.0, 3.0-10 micrometers (μm).
2. Initial resistance for the range of airflow rates as published by the manufacturer, including the maximum rated airflow rate. The selected airflow rates shall be in multiples of 400 cfm. If the maximum rated airflow rate is not a multiple of 400 cfm, then report initial resistance at multiples of 400 cfm, and any fraction thereof, to include the maximum rated airflow rate as described in subsections a, b, c, d, e below.
a. Airflow Rate Value 1 (val 1) = 400 cubic-feet-per-minute (cfm). If 400 cfm is not within the manufacturer's published range of airflow rates for the filter, value = N/A.
b. Airflow Rate Value 2 (val 2) = 800 cubic-feet-per-minute (cfm). If 800 cfm is not within the manufacturer's published range of airflow rates for the filter, value = N/A.
c. Airflow Rate Value 3 (val 3) = 1200 cubic-feet-per-minute (cfm). If 1200 cfm is not within the manufacturer's published range of airflow rates for the filter, value = N/A.
d. Airflow Rate Value 4 (val 4) = 1600 cubic-feet-per-minute (cfm). If 1600 cfm is not within the manufacturer's published range of airflow rates for the filter, value = N/A
e. Airflow Rate Value 5 (val 5) = Maximum Rated Airflow Rate (cfm).
3. Mark the non-reported MERV information field as “N/A.”
(B) Air filters for which reported information is determined in accordance with ASHRAE Standard 52.2-2012 shall be marked with the following information:
1. Particle size efficiency (PSE) of the unit in three particle size ranges: 0.3-1.0, 1.0-3.0, 3.0-10 micrometers (μm).
2. Initial resistance for the range of airflow rates as published by the manufacturer, including the maximum rated airflow rate. The airflow rate values shall be the maximum rated airflow rate, and the values for 50%, 75%, 100% and 125% of the test airflow rate value determined in accordance with ASHRAE 52.2-2012. as described in subsections a, b, c, d, e below.
a. Airflow Rate Value 1 (val 1) = 50% of the test airflow rate in cubic-feet-per-minute (50% of airflow rate value 3).
b. Airflow Rate Value 2 (val 2) = 75% of the test airflow rate in cubic-feet-per-minute (75% of airflow rate value 3).
c. Airflow Rate Value 3 (val 3) = 100% test airflow rate in cubic-feet-per-minute; determined as equal to selected test face velocity (feet per minute) multiplied by the air filter face area (square feet).
d. Airflow Rate Value 4 (val 4) = 125% of the test airflow rate in cubic-feet-per-minute (125% of airflow rate value 3.
e. Airflow Rate Value 5 (val 5) = Maximum Rated Airflow Rate (cfm).
3. Minimum Efficiency Reporting Value (MERV).
The information shall be disclosed in the format in Table Z.
Table Z
Sample Air Filter Marking
If the marking on the air filter is not legible through its retail packaging, then the packaging shall also be labeled with the same information and in the same format as Table Z. The requirements of this section shall not preclude manufacturers from providing additional information.
(13) State-Regulated LED Lamps. State-regulated LED lamps shall meet the criteria below before making any of the relevant claims in marketing materials, including retail packaging or on the lamp itself.
(A) For lamps manufactured on or after January 1, 2018, the following shall be demonstrated before making a claim of being “dimmable.”
1. The lamp shall be dimmable to 10 percent of its full light output.
2. The lamp shall be reduced flicker operation;
3. Shall not produce noise in excess of 24 A-weighted decibels at 100 percent and 20 percent of full light output.
4. If the product cannot be reduced flicker operation using a standard phase-cut dimmer, but can be reduced flicker operation using another type of dimmer, references to dimmability shall be qualified with the phrase “dimmable with LED dimmer.” These lamps shall include instructions on or inside the retail packaging that describe, or contain an internet link to a description of, the type of dimmers that are compatible or recommended for use with the lamp.
(B) State-regulated LED lamps manufactured on or after January 1, 2018 shall meet all of the following requirements before including comparisons to incandescent lamps:
1. The lamp shall have a correlated color temperature of 3000K or less.
2. The lamp shall be “dimmable” as described in 1607(d)(13)(A) of this Article.
3. The lamp shall have a lumen output of 310 lumens or greater for medium-screw base lamps or 150 lumens or greater for intermediate and candelabra bases.
EXCEPTION to section 1607(d)(13)(B): Section 1607(d)(13)(B) does not apply to incandescent wattage equivalency claims.
(C) If the manufacturer makes incandescent wattage equivalency claims for medium screwbase and GU24 base omnidirectional state-regulated LED lamps manufactured on or after January 1, 2018, the lamps shall have a minimum lumen output not less than the values shown in Table K-10.
Table K-10 Incandescent Wattage Equivalences for State-regulated LED Lamps
(D) A lamp manufactured on or after January 1, 2018 that is certified with a lumen output of less than 150 lumens for candelabra bases, or less than 200 lumens for other bases, shall be labeled on the retain packaging as “for decorative purposes.”
(E) For lamps manufactured on or after February 1, 2017, if the manufacturer makes any marketing, label, or mark regarding a model's qualification for the California Quality LED Lamp Specification, the manufacturer shall certify that the lamp model meets each and every portion of the California Quality LED Lamp Specification.
(14) Portable Electric Spas
(A) All portable electric spas manufactured on or after June 1, 2019, shall be marked by the manufacturer with the label specified in section 1607(d)(14)(B). The label shall be legible, conspicuously displayed to the consumer, and be removed only by the consumer.
1. For standard, exercise, and combination spas, the label shall be affixed on a readily visible location on the shell or skirt panel of the unit.
2. For inflatable spas, the label shall be affixed on a readily visible location on the unit's retail packaging.
(B) The label for all portable electric spas shall conform to the design specifications listed in subdivisions (d)(14)(B)1. through (d)(14)(B)4. in this section (inclusive). If the spa has been tested with multiple spa covers, the label shall display the most recent performance data, the model number, and the manufacturer, as listed in MAEDbS, of the tested spa cover of the spa unit-cover combination that yielded the maximum normalized standby power test result obtained in accordance with section 1605.3(g)(6)(B). The label may display the most recent spa cover model number(s) and corresponding spa cover manufacturer(s) for other covers tested with the unit. If the label lists multiple spa covers, the label shall display the spa cover model number(s) and corresponding spa cover manufacturer(s) of the spa covers tested with the unit as listed in MAEDbS.
1. Label Specifications. The label shall be formatted as shown in Figure 1 and as directed in subdivision (d)(14)(B)2. of this section.
Figure 1. Label Design
2. Letter Codes for Figure 1 Label Design. Letter codes for Figure 1 above:
a. Shall be printed on a white label with black text.
b. Minimum label width: 5 inches.
c. Minimum label height: 6.25 inches.
d. Leaf color: equivalent to Pantone 363 green (also permitted to be black).
e. Water drop color: equivalent to Pantone 7691 blue (also permitted to be black).
f. Font: Helvetica Neue Black; character height shall not be less than 15 point type. For standard spas, inflatable spas, and the standard spa portion of combination spas the text shall state the following: Portable Electric Spa. For exercise spas and the exercise spa portion of combination spas, the text shall state the following: Exercise Spa.
g. Font: Helvetica Neue Black; character height shall not be less than 24 point type. Text shall state the following: California ENERGY GUIDE.
h. Font: Arial Bold; character height shall not be less than 9.5 point type. Text shall state the following:
Manufacturer: [insert name of manufacturer here]
Model: [insert model number here]
Capacity (# of people): [insert number of people here].
i. Font: Arial Bold; character height shall not be less than 9.5 point type. Text shall state the following: Rated Volume.
j. Font: Arial Bold; character height shall not be less than 16 point type. The text shall state the value of the rated volume in U.S. gallons and shall state the units of the rated volume as follows: US Gal.
k. Font: Arial Bold; character height shall not be less than 16 point type. The text shall state the following: Standby Power* [insert the normalized standby power value resulting from the test in watts here, rounded to a whole number] Watts.
l. Font: Helvetica Neue Black; character height shall not be less than 24 point type. The text shall state the normalized standby power value resulting from the test in Watts, rounded to a whole number, and shall state the units of the tested standby power.
m. The standby power chart arrow shall be scaled at the appropriate location between the minimum and maximum power range using the normalized standby power test result value for the spa which is being installed. The minimum standby power shall be 50 watts, and the maximum standby power shall be 450 watts for standard spas, inflatable spas, and the standard spa portion of combination spas. The minimum standby power shall be 100 watts and the maximum standby power shall be 750 watts for exercise spas and the exercise spa portion of combination spas. If the normalized standby power test result is outside the power range, add or subtract, in increments of 50 watts, from the minimum or maximum power range values, until the normalized standby power test result is within the power range and update the minimum or maximum power range values on the label.
n. Font: Arial Bold; character height shall not be less than 12 point type.
o. Font: Arial Bold; character height shall not be less than 9.5 point type. The text shall state the following: Average Standby Power Range of Spa Models.
p. Font: Arial; character height shall not be less than 8 point type, and may be horizontally scaled to no less than 85 percent. The text shall state the following:
Maximum standby power allowed for this size spa under California Code of Regulations (CCR) Title 20, section 1605.3(g)(6)(B) and ANSI/APSP/ICC-14 2014: [insert the allowed maximum normalized standby power value based on fill volume, rounded to a whole number] Watts.
Total annual power consumption in standby mode*: [insert the normalized standby power value resulting from the test in watts here, rounded to a whole number] x Duty Cycle = [insert calculated value of total annual power consumption in standby mode here in kilowatts per hour, rounded to a whole number] kWh.
Annual Standby Energy Cost* = [insert total annual power consumption value here, rounded to a whole number] x Energy Rate (cost per kilowatt hour in your area).
*Data is based on standard test procedure for Portable Electric Spas as stipulated in CCR Title 20, section 1604(g)(2)(B) and ANSI/APSP/ICC-14 2014. Note: This is the amount of power used during test conditions and does not include spa usage or extreme cold conditions. This data should be used only for comparison of spa models. Power is not monthly energy consumption. Duty cycle is estimated to be [insert duty cycle value in hours here. For standard spas, exercise spas, and combinations spas insert 8,760. For inflatable spas, insert 5,040] hours per year.
Based on testing with the spa manufacturer's specified cover checked below, the spa cover-unit combination that yielded the highest normalized standby power. This spa must be sold with this cover or a manufacturer's approved equivalent that has also been tested with the unit per CCR Title 20, section 1608(a). To view the energy performance of the other covers specified below in combination with this unit, visit the California Energy Commission's Modern Appliance Efficiency Database System (MAEDbS).
Tested Cover Manufacturer(s): Empty Checkbox​ [insert name of manufacturer(s) here, names shall be preceded by a checkbox].
Tested Cover Model(s): Empty Checkbox​ [insert cover model number(s) here, model numbers shall be preceded by a checkbox].
q. The format for the maximum standby power value and total annual power consumption value is the following: Font: Arial Bold. Character height shall not be less than 8 point type and may be horizontally scaled to no less than 85 percent.
r. Font: Arial Bold; character height shall not be less than 8 point type, and may be horizontally scaled to no less than 85 percent. The text shall state the following: Power calculated based on standby mode testing. Actual values will vary based on use.
s. Font: Arial Bold; character height shall not be less than 8 point type, and may be horizontally scaled to no less than 85 percent. The text shall state the following: This Label Must Remain Adhered to Spa until Time of Sale to Consumer.
t. Font Arial; character height shall not be less than 8 point type, and may be horizontally scaled to no less than 85 percent. The text shall state the following: Printed on [insert the month, day, and year the label was printed on].
u. The checkbox of the tested spa cover model number and corresponding spa cover manufacturer coinciding with the performance data shall be marked on the label.
3. The label shall be printed:
a. on a removable adhesive-backed white polymer label or the equivalent for standard, exercise, and combination spas.
b. as specified in subdivision (d)(14)(B)3.a. or integrated as part of the unit's retail packaging design for inflatable spas.
4. All adhesive labels shall be applied so they can be easily removed without the use of tools or liquids, other than water, but shall be applied with an adhesive with an adhesion capacity sufficient to prevent dislodgment during normal handling throughout the chain of distribution to the consumer.
(15) Landscape Irrigation Equipment.
(A) Spray Sprinkler Bodies. Each spray sprinkler body manufactured on or after October 1, 2020, shall be marked, permanently and legibly, to indicate the presence of an internal pressure regulator. The marking shall be on an accessible and conspicuous place on the spray sprinkler body and designed to be visible after installation.
The following documents are incorporated by reference in section 1607.
Number
Title
CALIFORNIA ENERGY COMMISSION
California Energy Commission Voluntary California Quality Light Emitting Diode (LED) Lamp Specification (December 2017)
Copies available from:
CALIFORNIA ENERGY COMMISSION
ENERGY HOTLINE
1516 NINTH STREET, MS-25
SACRAMENTO, CALIFORNIA 95814
PHONE: (916) 654-5106
FAX: (916) 654-4304
FEDERAL MARKING REQUIREMENTS
C.F.R., Title 16, part 305
C.F.R., Title 10, section 430.32(w)(4)
Copies available from:
Superintendent of Documents
U.S. Government Printing Office
Washington, D.C. 20402
www.ecfr.gov
International Efficiency Marking Protocol for
External Power Supplies, Version 3.0,
September 2013
Copies available from:
U.S. Department of Energy,
Office of Energy Efficiency and
Renewable Energy, Forrestal Building,
Mail Station EE-2J,
1000 Independence Avenue, SW.,
Washington, DC 20585-0121
http://www.regulations.gov/contentStreamer?
documentId=EERE-2008-BT-
STD-0005-0218&disposition=
attachment&contentType=pdf
AMERICAN SOCIETY OF HEATING, REFRIGERATING AND AIR-CONDITIONING ENGINEERS (ASHRAE)
ANSI/ASHRAE/IES
90.1-2007
Energy Standard for Buildings Except
Low-Rise Residential Buildings
Copies available from:
American Society of Heating,
Refrigerating
and Air-Conditioning Engineers
1791 Tullie Circle N.E.
Atlanta, GA 30329
www.ashrae.org
Phone: (800) 527-4723 (U.S./Canada) or
(404) 636-8400
FAX: (404) 321-5478
Note: Authority cited: Sections 25213, 25218(e), 25401.9, 25402(a)-25402(c) and 25960, Public Resources Code. Reference: Sections 25216.5(d), 25401.9, 25402(a)-25402(c) and 25960, Public Resources Code.
HISTORY
1. Amendment filed 2-7-80; effective thirtieth day thereafter (Register 80, No. 6).
2. Renumbering and amendment of former section 1607 to section 1608 and renumbering and amendment of section 1606 to section 1607 filed 7-21-82; effective thirtieth day thereafter (Register 82, No. 30).
3. Amendment of subsection (a) filed 10-1-82; designated effective 6-2-83 (Register 82, No. 40).
4. New subsections (d), (e) and (f) filed 5-22-85; effective thirtieth day thereafter (Register 85, No. 21).
5. Amendment filed 10-23-86; effective thirtieth day thereafter (Register 86, No. 43).
6. Amendment of NOTE filed 7-20-87; operative 8-19-87 (Register 87, No. 30).
7. Amendment filed 8-29-88; operative 9-28-88 (Register 88, No. 37).
8. Amendment of subsections (a) and (b) and new subsection (h) filed 6-5-90; operative 7-5-90 (Register 90, No. 31).
9. Amendment of subsection (b) and adoption of Table G-2 filed 11-6-91; operative 12-6-91 (Register 92, No. 9).
10. Repealer and new subsection (h) filed 7-23-92; operative 8-24-92 (Register 92, No. 35).
11. Repealer and new section filed 10-28-2002; operative 11-27-2002 (Register 2002, No. 44).
12. Repealer of subsections (b)-(c), new subsections (b)-(c)(3) and repealer of subsection (d)(1)(A) designator and subsections (d)(1)(B)-(d)(1)(B)2. filed 4-1-2003 as an emergency; operative 4-1-2003 (Register 2003, No. 14). A Certificate of Compliance must be transmitted to OAL by 7-30-2003 or emergency language will be repealed by operation of law on the following day.
13. Certificate of Compliance as to 4-1-2003 order transmitted to OAL 7-8-2003 and filed 8-19-2003 (Register 2003, No. 34).
14. Amendment filed 3-16-2005; operative 4-15-2005 (Register 2005, No. 11).
15. Amendment of subsections (b)(1), (d)(1) and (d)(9)(i)a., new Exception to subsection (d)(9)(ii)d. and amendment of federal marking requirements filed 12-30-2005; operative 1-1-2006 pursuant to Government Code section 11343.4 (Register 2005, No. 52).
16. Amendment of subsections (d)(9)(i)a. and b., (d)(9)(ii)a. and Note filed 6-22-2006; operative 6-22-2006 pursuant to Government Code section 11343.4 (Register 2006, No. 25).
17. Amendment of subsection (d)(7) filed 12-14-2006; operative 12-14-2006 pursuant to Government Code section 11343.4 (Register 2006, No. 50).
18. Amendment of subsection (d) - Table W filed 8-22-2007; operative 9-17-2007 pursuant to Government Code section 11343.4 (Register 2007, No. 34).
19. Amendment filed 7-10-2009; operative 8-9-2009 (Register 2009, No. 28).
20. New subsections (d)(11)-(d)(11)(B) filed 9-1-2010; operative 1-1-2011 (Register 2010, No. 36).
21. New subsections (d)(12)-(13) filed 10-26-2012; operative 1-1-2013 (Register 2012, No. 43).
22. Amendment filed 4-22-2014; operative 7-1-2014 (Register 2014, No. 17).
23. Amendment of subsections (d)(8)(A)-(B), new subsections (d)(12)-(d)(12)(B)3. and amendment of list of documents incorporated by reference filed 6-30-2016; operative 7-1-2016 pursuant to Government Code section 11343.4(b)(3) (Register 2016, No. 27).
24. New subsections (d)(13)-(d)(13)(E) and amendment of list of documents incorporated by reference filed 11-1-2016; operative 1-1-2017 (Register 2016, No. 45).
25. Amendment of subsection (d)(12) filed 3-27-2017 as an emergency; operative 3-27-2017 (Register 2017, No. 13). A Certificate of Compliance must be transmitted to OAL by 9-25-2017 or emergency language will be repealed by operation of law on the following day.
26. Certificate of Compliance as to 3-27-2017 order transmitted to OAL 8-25-2017 and filed 10-5-2017 (Register 2017, No. 40).
27. New subsections (d)(14)-(d)(14)(B)4. filed 7-19-2018; operative 10-1-2019 (Register 2018, No. 29).
28. Amendment filed 9-26-2018; operative 10-1-2019 pursuant to Government Code section 11343.4(b)(3) (Register 2018, No. 39).
29. Editorial correction restoring inadvertently omitted subsection (d)(3) and amending subsection (d)(13)(B) (Register 2018, No. 45).
30. Change without regulatory effect amending subsections (d)(6) and (d)(9)(A)-(C) filed 3-18-2019 pursuant to section 100, title 1, California Code of Regulations (Register 2019, No. 12).
31. Amendment of subsection (c)(2), new subsections (d)(15)-(d)(15)(A) and amendment of Note filed 10-7-2019; operative 10-1-2020 pursuant to Government Code section 11343.4(b)(2) and Public Resources Code section 25402(c)(1) (Register 2019, No. 41).
This database is current through 9/11/20 Register 2020, No. 37
20 CCR § 1607, 20 CA ADC § 1607
End of Document© 2020 Thomson Reuters. No claim to original U.S. Government Works.