§ 2413. Emission Control Labels -- New Off-Highway Recreational Vehicles.
13 CA ADC § 2413Barclays Official California Code of Regulations
13 CCR § 2413
§ 2413. Emission Control Labels -- New Off-Highway Recreational Vehicles.
(a) Purpose. The Air Resources Board recognizes that certain emissions-critical or emissions-related parts must be properly identified and maintained in order for off-highway recreational vehicles, and engines used in such vehicles, to comply with the applicable emission standards. The purpose of this section is to require off-highway recreational vehicle engine manufacturers to attach a label (or labels) on each production vehicle (or engine) in order to provide vehicle owners and service mechanics with information necessary for the proper maintenance of these vehicles and engines in customer use.
(2) In selecting an acceptable location, the manufacturer shall consider the possibility of accidental damage (e.g., possibility of tools or sharp instruments coming in contact with the label). Each label shall be affixed in such a manner that it cannot be removed without destroying or defacing the label, and shall not be affixed to any part that is likely to be replaced during the vehicle's useful life.
(D) Identification of the Exhaust Emission Control System Abbreviations may be used and shall conform to the nomenclature and abbreviations found in the Society of Automotive Engineers' document J1930, which is incorporated by reference in section 1977, title 13, CCR, entitled “Electrical/Electronic Systems Diagnostic Terms, Definitions, Abbreviations, and Acronyms.”
(E) The tune-up specifications and adjustments recommended by the manufacturer, including, if applicable: valve lash, ignition timing, idle air fuel mixture setting procedure and value (e.g., CO, idle speed drop), and high idle speed. These specifications shall indicate the proper transmission position during tune-up and what accessories, if any, should be in operation, and what systems, if any (e.g., vacuum advance, air pump), should be disconnected during the tune-up. Any tune-up specifications or adjustment instructions that appear on labels shall be sufficiently clear and complete so as to preclude the need for a mechanic or vehicle owner to consult other references in order to correctly perform the adjustments. The manufacturer shall include the single statement: “No other adjustments needed,” in lieu of any tune-up adjustment instruction, when the manufacturer does not recommend a tune-up specification or an adjustment.
(G) An unconditional statement of compliance with the appropriate model-year California regulations. For example, “This (specify off-road motorcycle, all-terrain vehicle, off-road sport vehicle, off-road utility vehicle, sand car, or engine, as applicable) conforms to California regulations applicable to (specify applicable model year) model-year new (specify off-road motorcycles, all-terrain vehicles, off-road sport vehicles, off-road utility vehicles, sand cars, or engines, as applicable). The statement shall also include the phrase, “is certified to (specify applicable HC standard in grams per kilometer) HC engine family exhaust emission standard in California” or the phrase “is certified to (specify applicable HC+NOx standard in grams per kilowatt-hour) HC+NOx engine family exhaust emission standard in California.”
(5) A manufacturer may elect to use a supplemental label when the original label lacks sufficient space to include all the required information. A supplemental label shall conform to all of the specifications as the original label. The original label shall be indicated as “1 of 2” and the supplemental label shall be indicated as “2 of 2” whenever a supplemental label is utilized.
(6) The provisions of this section shall not prevent a manufacturer from also reciting on the label that such off-highway recreational vehicle or engine conforms to any applicable federal emission standards for new off-road motorcycles, all-terrain vehicles, off-road utility vehicles or engines used in such vehicles, or any other information that such manufacturer deems necessary for, or useful to, the proper operation and satisfactory maintenance of such off-highway vehicles or engines.
(7) As used in this Section 2413(c), readily visible to the average person means that the label shall be readable from a distance of 18 inches (46 centimeters) without any obstructions from vehicle or engine parts (including all manufacturer available optional equipment) except for flexible parts (e.g., vacuum hoses, ignition wires) that can be moved out of the way without disconnection. Alternatively, information required by these specifications to be printed on the label shall be no smaller than 8 point type size (2 millimeters in height) provided that no vehicle or engine parts (including all manufacturer available optional equipment), except for flexible parts, obstruct the label.
(8) The labels and any adhesives used shall be designed to withstand, for the off-highway recreational vehicle's total expected life, typical off-highway recreational vehicle environmental conditions at the location where a label has been attached. Typical off-highway recreational vehicle environmental conditions include, but are not limited to, exposure to engine fuels, lubricants and coolants (e.g., gasoline, motor oil, brake fluids, ethylene glycol), engine operating temperatures, steam cleaning, and paints or paint solvents. The manufacturer must submit, with its certification application, a statement attesting that its labels comply with this requirement.
(9) The manufacturer must obtain approval from the Executive Officer for all emission control label formats and locations prior to certification. Approval of the specific tune-up specifications and adjustments is not required; however, the format for all such specifications and adjustments, if any, is subject to review. If the Executive Officer finds that the information on the label is vague or subject to misinterpretation, or that the location does not comply with these specifications, the Executive Officer may require that the label or its location be modified accordingly.
(12) If the Executive Officer finds any off-highway recreational vehicle or engine manufacturer using emission control labels that are different from those approved or that do not substantially comply with the readability or durability requirements set forth in this section, the Executive Officer may invoke section 2109, title 13, California Code of Regulations.
Credits
Note: Authority cited: Sections 39600, 39601, 43013, 43018, 43105 and 43107, Health and Safety Code. Reference: Sections 43013, 43018, 43102, 43105 and 43107, Health and Safety Code.
History
1. New section filed 1-26-95; operative 1-26-95 pursuant to Government Code section 11343.4(d) (Register 95, No. 4). Note: Under section 209(e)(2) of the Federal Clean Air Act (42 U.S.C. § 7543(e)(2)), California is required to receive authorization from the Administrator of the U.S. Environmental Protection Agency (U.S. EPA) prior to enforcing its regulations regarding new off-road vehicles and engines. Accordingly, the Air Resources Board will not seek to enforce the off-highway recreational vehicle regulations until such time as it receives authorization from the U.S. EPA.
2. U.S. EPA granted California authorization on December 23, 1996 (61 Fed.Reg. 69093, December 31, 1996).
3. Amendment of subsection (b) filed 3-23-99; operative 3-23-99 pursuant to Government Code section 11343.4(d) (Register 99, No. 13).
4. Repealer of subsection (a) designator and repealer of subsection (b) filed 10-19-99; operative 11-18-99 (Register 99, No. 43).
5. Amendment filed 12-8-99; operative 1-7-2000 (Register 99, No. 50).
6. Amendment of section and Note filed 7-16-2007; operative 8-15-2007 (Register 2007, No. 29).
This database is current through 4/26/24 Register 2024, No. 17.
Cal. Admin. Code tit. 13, § 2413, 13 CA ADC § 2413
End of Document |